R.E.V. T01 Keen

Inflator System · Connector Units

R.E.V. T01 Keen

Combines integrated, pull-actuated exhaust with low-profile geometry and an elliptical hose interface to reduce bulk and snag exposure, with native compatibility across the T01 Series flange family.
Mount standard · Corrugated hose interface:

CONFIGURATION

Series Interface
T01

Connector Installed Profile
Low · 33.0 mm (1.30 in)

Nut Design
Stone

Internal Cable

Requires a compatible Internal Cable. Already have one? No additional cable is needed.

 View Internal Cable

Be notified when this product becomes available.

 Join the waitlist
R.E.V. T01 Keen connector, side view of the wing-tab locking ring and low-profile bend
  • R.E.V. T01 Keen connector, side view of the wing-tab locking ring and low-profile bend
  • T01 Keen front view showing the round outlet port set into the wing-tab ring
  • T01 Keen locking ring shown isolated, triangular grip tabs with T01 Series mark
  • T01 Keen dome cap with HYDPRO wordmark, mounted on the wing-tab locking ring
  • T01 Keen clear ring accessory, isolated product shot
  • R.E.V. T01 Keen three-quarter view from above showing the open outlet and exhaust valve
  • R.E.V. T01 Keen connector, side view of the wing-tab locking ring and low-profile bend
  • T01 Keen front view showing the round outlet port set into the wing-tab ring
  • T01 Keen locking ring shown isolated, triangular grip tabs with T01 Series mark
  • T01 Keen dome cap with HYDPRO wordmark, mounted on the wing-tab locking ring
  • T01 Keen clear ring accessory, isolated product shot
  • R.E.V. T01 Keen three-quarter view from above showing the open outlet and exhaust valve
Close-up of a drysuit valve with corrugated hoses on a diver's chest

R.E.V. T01 Series

Low-profile clearance with pull-actuated exhaust.

R.E.V. T01 Keen: rapid-exhaust connector, elliptical low-profile body, T01 47mm interface, stone nut profile

Specifications

Rapid exhaust. Keen profile. T01 interface.

R.e.v. T01 Keen connector: integrated, pull-actuated exhaust. Features low-profile geometry and an elliptical hose interface to reduce bulk and snag exposure. Engineered around the T01 flange interface for full compatibility with all T01 Series flanges.

 Full technical specs (PDF)

Extended Mount Compatibility

Engineered for cross-platform integration, HYDPRO Connector Units are available in T23 and T25 Mount Standards, specifically configured for 23.6 mm (0.93 in) and 25.4 mm (1.00 in) corrugated hoses.

Built to integrate. True to your setup.

Whatever the field runs, HYDPRO builds to it natively: every established mount standard, thread, and host geometry, covered from the factory. Your setup stays as it is, integration stays clean, and the response repeats: the same command, the same result, on every dive.

Italian engineering. Predictable control

Each HYDPRO device is engineered and manufactured in Italy: one chain from raw material to release. Polymer families are selected for constant immersion, precision-drawn brass runs on in-house CNC lines, and every device leaves built, tested, and signed off under one roof.
HYDPRO power unit manufacturing: CNC machining, hand assembly, and the finished valve underwater

Proven by divers.
Refined by decades.

Four decades in the water stand behind the current generation. What wears, what binds, what drifts out of tune comes back from real dives to the bench, and the next revision answers it. Control you can feel, refined one generation at a time.

Featured Products

View all

R.E.V. T02 Keen

R.E.V. T02 Keen

Low-profile clearance with pull-actuated exhaust.

Rapid Exhaust Valve