Pipe P03 Keen

Inflator System · Connector Units

Pipe P03 Keen

Combines fixed elbow routing with patented Core-Sink Technology and Keen geometry for ultra-flat integration and reduced bulk, with native compatibility across the P03 Series flange family.
Mount standard · Corrugated hose interface:

CONFIGURATION

Series Interface
P03

Connector Installed Profile
Ultra-flat · 21.2 mm (0.83 in)

Nut Design

Sharp

Internal Cable

Requires a compatible Internal Cable. Already have one? No additional cable is needed.

 View Internal Cable

Be notified when this product becomes available.

 Join the waitlist
Pipe P03 Keen connector, side view of the ultra-flat elbow with angular locking ring and tapered barb
  • Pipe P03 Keen connector, side view of the ultra-flat elbow with angular locking ring and tapered barb
  • Front view into the tapered port of the Pipe P03 Keen, angular-tooth P03 Series locking ring visible
  • Angular-tooth locking ring for the Pipe P03 Keen shown alone, three-quarter angle
  • Front elevation of the Pipe P03 Keen elbow bend rising from its angular-tooth locking ring
  • Oval sealing gasket matching the Pipe P03 Keen elliptical hose interface
  • Rear three-quarter view of the Pipe P03 Keen elbow showing the faceted base disk and tapered barb
  • Pipe P03 Keen connector, side view of the ultra-flat elbow with angular locking ring and tapered barb
  • Front view into the tapered port of the Pipe P03 Keen, angular-tooth P03 Series locking ring visible
  • Angular-tooth locking ring for the Pipe P03 Keen shown alone, three-quarter angle
  • Front elevation of the Pipe P03 Keen elbow bend rising from its angular-tooth locking ring
  • Oval sealing gasket matching the Pipe P03 Keen elliptical hose interface
  • Rear three-quarter view of the Pipe P03 Keen elbow showing the faceted base disk and tapered barb

Pipe P03 Series

Ultra-flat integration for clean hose routing.

Pipe P03 Keen: elbow connector, ultra-flat P03 interface with patented Core-Sink tech, sharp nut profile

Specifications

Clean routing. Ultra-flat profile. P03 interface.

Pipe P03 Keen connector: fixed elbow routing. Features an ultra-flat profile, enabled by patented Core-Sink Technology, paired with the Keen low-profile geometry to minimize bulk. Engineered around the P03 flange interface for full compatibility with all P03 Series flanges.

 Full technical specs (PDF)

Extended Mount Compatibility

Engineered for cross-platform integration, HYDPRO Connector Units are available in T23 and T25 Mount Standards, specifically configured for 23.6 mm (0.93 in) and 25.4 mm (1.00 in) corrugated hoses.

Built to integrate. True to your setup.

Whatever the field runs, HYDPRO builds to it natively: every established mount standard, thread, and host geometry, covered from the factory. Your setup stays as it is, integration stays clean, and the response repeats: the same command, the same result, on every dive.

Italian engineering. Predictable control

Each HYDPRO device is engineered and manufactured in Italy: one chain from raw material to release. Polymer families are selected for constant immersion, precision-drawn brass runs on in-house CNC lines, and every device leaves built, tested, and signed off under one roof.
HYDPRO power unit manufacturing: CNC machining, hand assembly, and the finished valve underwater

Proven by divers.
Refined by decades.

Four decades in the water stand behind the current generation. What wears, what binds, what drifts out of tune comes back from real dives to the bench, and the next revision answers it. Control you can feel, refined one generation at a time.

Featured Products

View all

R.E.V. T02 Keen

R.E.V. T02 Keen

Low-profile clearance with pull-actuated exhaust.

Rapid Exhaust Valve