Pipe P01 Keen

Inflator System · Connector Units

Pipe P01 Keen

Combines fixed elbow routing with low-profile geometry and an elliptical hose interface to reduce bulk and snag exposure, with native compatibility across the P01 Series flange family.
Mount standard · Corrugated hose interface:

CONFIGURATION

Series Interface
P01

Connector Installed Profile
Low · 29.1 mm (1.15 in)

Nut Design
Ridge

Internal Cable

Requires a compatible Internal Cable. Already have one? No additional cable is needed.

 View Internal Cable

Be notified when this product becomes available.

 Join the waitlist
Pipe P01 Keen connector, side view of the low-profile elbow with tapered hose barb and fluted ring
  • Pipe P01 Keen connector, side view of the low-profile elbow with tapered hose barb and fluted ring
  • Front view into the tapered port of the Pipe P01 Keen, fluted P01 Series locking ring visible
  • Fluted locking ring for the Pipe P01 Keen shown alone, three-quarter angle
  • Front elevation of the Pipe P01 Keen elbow bend rising from its fluted locking ring
  • Circular sealing gasket sized for the Pipe P01 Keen hose interface
  • Rear three-quarter view of the Pipe P01 Keen elbow showing the fluted base disk and tapered barb
  • Pipe P01 Keen connector, side view of the low-profile elbow with tapered hose barb and fluted ring
  • Front view into the tapered port of the Pipe P01 Keen, fluted P01 Series locking ring visible
  • Fluted locking ring for the Pipe P01 Keen shown alone, three-quarter angle
  • Front elevation of the Pipe P01 Keen elbow bend rising from its fluted locking ring
  • Circular sealing gasket sized for the Pipe P01 Keen hose interface
  • Rear three-quarter view of the Pipe P01 Keen elbow showing the fluted base disk and tapered barb

Pipe P01 Series

Low-profile clearance for clean hose routing.

Pipe P01 Keen: elbow connector, standard P01 interface, elliptical body, ridge and stone nut profiles

Specifications

Clean routing. Keen profile. P01 interface.

Pipe P01 Keen connector: fixed elbow routing. Features low-profile geometry and an elliptical hose interface to reduce bulk and snag exposure. Engineered around the P01 flange interface for full compatibility with all P01 Series flanges.

 Full technical specs (PDF)

Extended Mount Compatibility

Engineered for cross-platform integration, HYDPRO Connector Units are available in T23 and T25 Mount Standards, specifically configured for 23.6 mm (0.93 in) and 25.4 mm (1.00 in) corrugated hoses.

Built to integrate. True to your setup.

Whatever the field runs, HYDPRO builds to it natively: every established mount standard, thread, and host geometry, covered from the factory. Your setup stays as it is, integration stays clean, and the response repeats: the same command, the same result, on every dive.

Italian engineering. Predictable control

Each HYDPRO device is engineered and manufactured in Italy: one chain from raw material to release. Polymer families are selected for constant immersion, precision-drawn brass runs on in-house CNC lines, and every device leaves built, tested, and signed off under one roof.
HYDPRO power unit manufacturing: CNC machining, hand assembly, and the finished valve underwater

Proven by divers.
Refined by decades.

Four decades in the water stand behind the current generation. What wears, what binds, what drifts out of tune comes back from real dives to the bench, and the next revision answers it. Control you can feel, refined one generation at a time.

Featured Products

View all

R.E.V. T02 Keen

R.E.V. T02 Keen

Low-profile clearance with pull-actuated exhaust.

Rapid Exhaust Valve